• <acronym id="u6ci2"><tt id="u6ci2"></tt></acronym>
  • <td id="u6ci2"><rt id="u6ci2"></rt></td>
    葛利茲模具鋼材-名佳利銅帶材-新東透氣鋼華南區代理之產品展示

    新東透氣鋼的設計要求和安裝

    設計porcerax II排氣鋼時,應考慮以下準則:

    1.使用的樹脂

    根據成型過程中的氣體排放量或殘留評估使用7或20微米孔徑。如7微米小氣孔新東透氣鋼,在ABS、聚丙烯樹脂、軟型聚氯乙烯、聚乙烯、聚丙烯、聚氨酯、苯乙烯中表現良好,對于低粘度或滑石粉填充樹脂,它可能需要有一個自動化的系統反向氣流互射清除毛孔后的雜質,硬質PVC樹脂也適用,但隨著被氣體長期腐蝕,透氣孔會堵塞,如果工件不需要重復利用,這仍然是一個可行方案。
    在排氣量非常多時,建議采用20微米孔徑的新東新東透氣鋼。20微米慪氣剛的開發是為了滿足研磨后直接使用,經過正確的研磨,20微米新東透氣鋼留下的氣孔是部分開放(約40-50%)。然而,使用20微米孔徑的新東透氣鋼,并保持20微米孔徑,通過電火花加工或研磨拋光后,透氣性比7微米更好,但是它也將堵塞得更快。

    2.排氣區域的面積大小

    建議核心腔面積至少10%是PORCERAX II新東透氣鋼,以確保穩定的排氣。雖然這并非總是必要的,它是要記住,在模芯和腔區域中的使用面積,帶來的較低的背壓是重要的。由于較大的表面積,該新東透氣鋼工件不需要經常清洗薄的PORCERAX新東透氣鋼透氣性能會更好,不過要注意PORCERAXⅡ新東透氣鋼的機械性能。太薄的透氣鋼零件可能無法承受注塑壓力。

    3.表面光潔度要求

    由于大多數的新東透氣鋼都是應用在模芯側面來解決,如果電火花的光潔度可以接受,排氣性能會是最高的。如果有更高的光潔度要求,研磨拋光的表面將提供一個最好的排氣表面。重要的是,如果新東透氣鋼在模具的模腔側使用,光澤度就會受到嚴重降低(#9到#2-3與PP),所以需要考慮是否匹配設計要求。

    4.透氣鋼的各種安裝槽設計圖紙





    Porcerax II
    Design Guidelines
    When designing for Porcerax II venting steel, the following guidelines should be considered:
    Resins Used
    Depending on the emissions or gas residue given off during the molding process, the molder will have to evaluate whether to use a 7 or 20-micron pore size. Resins such as ABS, polypropylene, soft type PVC, polyethylene, acrylic, polyurethane, and styrene work very well with a 7-micron pore size. For low viscosity or talc-filled resins, it may be necessary to have an automated system reverse the airflow after each shot to purge the impurities from the pores. Rigid PVC resins will work, but only until the corrosive gases close the pores. This can still be a feasible method if disposable inserts are used. Where extreme venting is needed, a 20-micron pore size is recommended. The 20-micron grade was developed to be used with a milled finish. When milled properly this process with the 20-micron material leaves a pore that is partially open (about 40-50 %). However, using the 20-micron pore size material and maintaining the 20-micron pore size, by EDM or polishing after milling, will vent better than 7-micron, but it will also clog faster.
    Size of Area to be Vented
    The producing mill recommends that at least 10% of the core and cavity area be Porcerax II to insure proper venting. While this is not always possible, it is important to remember that the more square inches used in the core and cavity area, the lower the back pressure will be in the cavity. Due to the larger surface area, the insert will not require cleaning as often as a smaller piece. If Porcerax II is used as a core or cavity half, instead of as an insert, there may not be a need for parting line vents.
    Note:The thinner the Porcerax or the shorter the distance air has to travel to the exhaust
    line the better the venting will be. Keep in mind the physical properties of Porcerax II.
    Note:Porcerax is typically inserted on the core side of the mold in the problem area in
    order to hide insert lines.
    Surface Finish Requirements
    Since most applications can be addressed using inserted pieces on the core side, an EDM finish is acceptable and will vent better than any other surface finish. Should EDM be impractical, a stoned or polished surface will provide the next best venting surface. It is important to remember that if the venting steel is used on the cavity side of a mold, the gloss level will be severely reduced (#9 to a #2-3 with PP), so matching should be considered.
    If a low gloss level on a textured part is desired, it can be accomplished with the 7-micron Porcerax II. Certain procedures must be followed to prevent the possible, irreversible damage to the internal pore structure of the material. The texturing house selected for this procedure must be advised that they will be texturing porous, venting steel. The pores must be thoroughly cleaned and sealed prior to texturing. This insures the acid used to etch the surface does not run through the material corroding the interior structure. Performed properly, texturing Porcerax II will give the molder an unmatched finish in terms of definition.
    Slide/Lifter Applications
    Porcerax II can be used in slide or lifter applications. However, it is important to consider lubrication requirements on such a design. Lubricants will, in all likelihood, reduce or eliminate permeability in areas that come into contact with Porcerax II.
    本文出自*港峰公司*,轉載請注明出處!

    發表時間:2016/5/12 20:11:14打印此頁 推薦給好朋友 收藏此頁
    關于港峰產品展示葛利茲特鋼名佳利銅帶鑼磨加工技術資料企業資訊聯系我們站內搜索(百度LOGO)
    Copyright © 2005-2016 GangFeng Corporation,All Rights Reserved  粵ICP備16032059
    国色天香一卡二卡三卡四卡视,日本一卡二卡三卡四卡,卡一卡二卡三乱码,亚洲不卡一卡二卡三新区,日本卡一卡二卡三卡四 国产亚洲一卡2卡3卡四卡国色天香| 欧美日韩一卡2卡3卡4卡5卡视频| 精品一卡2卡三卡4卡乱码视频| 欧美日韩一卡2卡3卡4卡新区| 欧洲一卡2卡三卡4卡乱码毛1| 欧美日韩一卡二卡三卡| 精品一卡2卡三卡4卡棋牌| 成片2021一卡2卡三卡4卡乱码不卡| 欧美日韩2020卡二卡三卡四乱码| 欧美日韩一区二区三区| 精品一卡2卡3卡四卡国色天香| 国产亚洲一卡二卡三新区入口| 欧洲一卡2卡3卡四卡网站| 欧洲高清无卡码一区二区三区| 国产亚洲卡一卡二卡三专区免费| 国产亚洲一卡二卡3卡4卡网站| 成片伦一区二区三区视频| 国产亚洲一卡2卡3卡4卡乱码在线| 精品一卡二卡3卡四卡免费| 成片一卡二卡≡卡四卡高清乱码| 欧美日韩一卡2卡3卡4卡2021乱码在线观看| 欧洲卡1卡2乱码免费| 欧美日韩伦一区二区三区视频| 国产亚洲一卡2卡3卡4卡新区| 精品一卡2卡3卡4卡新区| 成片一卡2卡3卡4卡国色天香九零| 欧美日韩中文字乱码卡一卡二| 欧美日韩不卡一卡2卡三卡4卡5卡| 国产亚洲一本二卡三卡四卡无卡免费高| 国产亚洲一卡三卡四区一卡三卡| 欧洲一卡2卡3卡4卡免费观看| 精品一卡二卡≡卡四卡在线视频| 国产亚洲2021卡一卡二乱码| 欧洲2020卡二卡三卡四乱码| 欧美日韩一卡2卡3卡4卡5卡在线| 欧洲一卡一卡高清在线观看| 欧美日韩一本大道卡2卡3卡4卡| 精品免费一卡三卡四卡| 精品伦一区二区三区视频| 欧美日韩一卡2卡三卡4卡棋牌| 国产亚洲一卡2卡3卡4卡乱码网站导航| 欧美日韩一卡2卡3卡4卡网站动漫| 欧美日韩一卡一卡高清在线观看| 国产亚洲一卡2卡三卡4卡棋牌| 国产亚洲e本大道二卡三卡免费| 欧美日韩卡1卡2卡三卡2021| 欧洲卡1卡2乱码免费| 欧洲2018一卡2卡3卡4卡网站| 成片一卡2卡3卡4卡国色天香九零| 精品一本到卡二卡三卡免费乱码| 欧美日韩一卡二卡≡卡四卡高清乱码| 欧美日韩1卡二卡三卡4卡| 欧美日韩一卡二卡3卡四卡免费| 成片2020卡二卡三卡四乱码| 国产亚洲一卡一卡高清在线观看| 欧美日韩一卡2卡3卡四卡网站| 成片伦一区二区三区视频|